Abstract: The differential impact on soil organic carbon (SOC) of applying no tillage (NT) compared to conventional tillage (CT, i.e. mouldboard ploughing), along with three rates of nitrogen (N) fertilizer application (0,90 and 180 kg ha(-1) y(-1)), was studied under rain-fed Mediterranean conditions in a long-term experiment based on a durum wheat-maize rotation, in which crop residues were left on the soil (NT) or incorporated (CT). Observed SOC content following 8 and 12 years of continuous treatment application was significantly higher in the top 10 cm of the soil under NT than CT, but it was similar in the 10-40 cm layer. NT grain yields for both maize and durum wheat were below those attained under CT (on average 32% and 14% lower respectively) at a given rate of N fertilizer application. Soil, climate and crop data over 5 years were used to calibrate DSSAT model in order to simulate the impact of the different management practices over a 50-year period. Good agreement was obtained between observed and simulated values for crops grain yield, above-ground biomass and observed SOC values. Results from the simulations showed that under NT the weeds growing during the intercrop fallow period made a significant contribution to the observed SOC increase. When the contribution of the weed fallow was considered, NT significantly increased SOC in the top 40 cm of the soil at an average rate of 0.43, 0.31 and 0.03 t ha(-1) per year, respectively for 180,90 and 0 kg N ha(-1) year(-1), within the simulated 50 years. Under CT, a significant SOC increase was simulated under N180 and a significant decrease when no fertilizer was supplied.

Abstract: Agricultural crops are affected by climate change due to the relationship between crop development, growth, yield, CO2 atmospheric concentration and climate conditions. In particular, the further reduction in existing limited water resources combined with an increase in temperature may result in higher impacts on agricultural crops in the Mediterranean area than in other regions. In this study, the cropping system models CERES-Wheat and CROPGRO-Tomato of the Decision Support System for Agrotechnology Transfer (DSSAT) were used to analyse the response of winter durum wheat (Triticum aestivum L.) and tomato (Lycopersicon esculentum Mill.) crops to climate change, irrigation and nitrogen fertilizer managements in one of most productive areas of Italy (i.e. Capitanata, Puglia). For this analysis, three climatic datasets were used: (1) a single dataset (50 km x 50 km) provided by the JRC European centre for the period 1975-2005; two datasets from HadCM3 for the IPCC A2 GHG scenario for time slices with +2A degrees C (centred over 2030-2060) and +5A degrees C (centred over 2070-2099), respectively. All three datasets were used to generate synthetic climate series using a weather simulator (model LARS-WG). Adaptation strategies, such as irrigation and N fertilizer managements, have been investigated to either avoid or at least reduce the negative impacts induced by climate change impacts for both crops. Warmer temperatures were primarily shown to accelerate wheat and tomato phenology, thereby resulting in decreased total dry matter accumulation for both tomato and wheat under the +5A degrees C future climate scenario. Under the +2A degrees C scenario, dry matter accumulation and resulting yield were also reduced for tomato, whereas no negative yield effects were observed for winter durum wheat. In general, limiting the global mean temperature change of 2A degrees C, the application of adaptation strategies (irrigation and nitrogen fertilization) showed a positive effect in minimizing the negative impacts of climate change on productivity of tomato cultivated in southern Italy.

Abstract: The aim of this paper is to provide a critical analysis of the strengths and weaknesses of a non-standardised Model Requirements Analysis (MRA) used for the purpose of developing the Sustainability Impact Assessment Tool (SIAT). By ‘non-standardised’ we mean not strictly following a published MRA method. The underlying question we are interested in addressing is how non-standardised methods, often employed in research driven projects, compare to defined methods with more standardised structure, with regards their ability to capture model requirements effectively, and with regards their overall usability. Through describing and critically assessing the specific features of the non-standardised MRA employed, the ambition of this paper is to provide insights useful for impact assessment tool (IAT) development. Specifically, the paper will (i) characterise kinds of user requirements relevant to the functionality and design of IATs; (ii) highlight the strengths and weaknesses of non-standardised MRA for user requirements capture, analysis and reflection in the context of IAT; (iii) critically reflect on the process and outcomes of having used a non-standardised MRA in comparison with other more standardised approaches. To accomplish these aims, we first review methods available for IAT development before describing the SIAT development process, including the MRA employed. Major strengths and weaknesses of the MRA method are then discussed in terms of user identification and characterisation, organisational characterisation and embedding, and ability to capture design options for ensuring usability and usefulness. A detailed assessment on the structural differences of MRA with two advanced approaches (Integrated DSS design and goal directed design) and their role in performance of the MRA tool is used to critique the approach employed. The results show that MRA is able to bring thematic integration, establish system performance and technical thresholds as well as detailing quality and transparency guidelines. Nevertheless the discussion points out to a number of deficiencies in application – (i) a need to more effectively characterise potential users, and; (ii) a need to better foster communication among the distinguished roles in the development process. If addressed these deficiencies, SIAT non-standardised MRA could have brought out better outcomes in terms of tool usability and usefulness, and improved embedding of the tool into conditions of targeted end-users. (C) 2013 Elsevier Ltd. All rights reserved.